Comments
-
One more time: they are in the Custom Blocks menu of the Project #25.
<… -
We'll let in Splitting The Picobricks System Comment by Turgut November 2022
-
Pin descriptions for the HC-05 is right next to the black socket for the HC-05, as well as …
-
Project #25 Custom Blocks menu has all the ESP01 functionality for the project provided.
- Corrected to My Blocks menu.
-
There is no library code for the ESP01. Instead there is a project #25 Smart Green House that uses the ESP01 as a server. All the ESP011 codes needed for that project is under Custom Blocks. This project is an advanced pr…
-
I am reviewing all the projects this week and next. Robotistan team is new to the MicroBloc…
-
There's an rtc in the pico 2040, but there are to issues with it:
- it is not sub-second capable
- there is no built-in battery, so it cannot persist.
- also. from MicroBlocks, there is no block to accees the rtc component o…
-
Sorry Peter, by the time I submitted my response, you had already posted…
-
Selected Library Load can be accomplished by saving an empty project with the desired libra…
-
-
@barriereg , in HC05 Not Working Comment by Turgut November 2022
-
Did you try getting into config mode?
-
Sorry about my previous reply. I just realized there were two parts to your problem:
-
This link will help you maybe: The issue is the Apple cell !
in HC05 Not Working Comment by Turgut November 2022
-
@wfortuny, in HC05 Not Working Comment by Turgut November 2022
-
While you are running the mobile APP, observe the RED LED.
It should be in two flashes every five sec mode for normal operation, while transmitting the car commands.
If it switches to the rapid flash mode, then the APP has lost connec…
-
HC-05 Users,
You cannot use the module blindly. Need to know what state it is in and its default settings.
Normally, the module will have a RESET button on it to put it into CONFIG mode.
Pressing the button, insert it …
-
I don't know if this will help you at all, but here are the pin assignments as used by th…
-
Hi everyone,
We have found a strange timing problem with the DHT library and fixed it. The new release will include the fix.
Until than, if you want to make the Temperature project (or any project with the DHT11) work reliably, pleas…
-
Users with DHT problem in MicroBlocks:
Provided you are running the latest versin of IDE and FW, please try the code with a 500ms delay inserted at end of the loop. That would be a wait 500ms block from the control category. It should go ri…
-
Can you confirm something for me:
If you place a PB temperature block on the IDE and click on it, do…
-
Thanks for bringing this to our attention. The spacing problem for the display digits…
-
Do you still have the problem?
If so, please share your MicroBlocks IDE and Firmware levels dis…
-
@chad and others, experiencing i2c and other errors with MicroBlocks:
Your experiences point to an out of synch condition between the code on the board and the IDE, which can be caused by various things. Regarding DHT module errors, we hav…
-
PicoBricks kit includes an ESP01 Serial WIFI component, which works with the AT-command set over the Serial interface.
Depending on your programming competence and language you are using, you might find that working with the ESP01 versus Pi…
-
Yours is a way to handle the edit delays present in the older versions of the firmware.
… -
Thanks for this. When I wrote the Oct.21 post above, I forgot to mention that Pico has t…
-
PB button block reports its state at the instant it is executed. Thus, when the button is press…
-
Hi,
To help all of you to sort out the problem, let's review the two way you can connect a PICO to the computer:
- BOOTSEL button pressed and then plugged into the USB port
- Plugged into the USB with…
Howdy, Stranger!